Difference between revisions of "7501T8"
From Sensoray Technical Wiki
|
|
| (36 intermediate revisions by one user not shown) |
| Line 1: |
Line 1: |
| − | Model 7501T8 is a solid-state relay (SSR) rack that accommodates up to eight G4 type SSR modules. It has a 50-pin header which is compatible with several Sensoray GPIO products, including models 826 and 2410.
| + | #REDIRECT [[7501Tx relay racks]] |
| − | | + | [[Category:Products]] |
| − | ==Pinout==
| + | |
| − | | + | |
| − | {| class="wikitable"
| + | |
| − | ! SSR<br>Module
| + | |
| − | ! Header<br>Pin
| + | |
| − | ! Terminal<br>Block Pins
| + | |
| − | ! Model 826<br>J3 GPIO
| + | |
| − | ! Model 826<br>J4 GPIO
| + | |
| − | ! Model 2410<br>GPIO
| + | |
| − | |-
| + | |
| − | |0
| + | |
| − | |47
| + | |
| − | |1-2
| + | |
| − | |0
| + | |
| − | |24
| + | |
| − | |17
| + | |
| − | |-
| + | |
| − | |1
| + | |
| − | |45
| + | |
| − | |3-4
| + | |
| − | |1
| + | |
| − | |25
| + | |
| − | |19
| + | |
| − | |-
| + | |
| − | |2
| + | |
| − | |43
| + | |
| − | |5-6
| + | |
| − | |2
| + | |
| − | |26
| + | |
| − | |21
| + | |
| − | |-
| + | |
| − | |3
| + | |
| − | |41
| + | |
| − | |7-8
| + | |
| − | |3
| + | |
| − | |27
| + | |
| − | |23
| + | |
| − | |-
| + | |
| − | |4
| + | |
| − | |39
| + | |
| − | |9-10
| + | |
| − | |4
| + | |
| − | |28
| + | |
| − | |9
| + | |
| − | |-
| + | |
| − | |5
| + | |
| − | |37
| + | |
| − | |11-12
| + | |
| − | |5
| + | |
| − | |29
| + | |
| − | |11
| + | |
| − | |-
| + | |
| − | |6
| + | |
| − | |35
| + | |
| − | |13-14
| + | |
| − | |6
| + | |
| − | |31
| + | |
| − | |13
| + | |
| − | |-
| + | |
| − | |7
| + | |
| − | |33
| + | |
| − | |15-16
| + | |
| − | |7
| + | |
| − | |31
| + | |
| − | |15
| + | |
| − | |}
| + | |
| − | | + | |
| − | ==Using with model 826==
| + | |
| − | | + | |
| − | The relay rack can be connected to header J3 or J2 on the 826 board.
| + | |
| − | | + | |
| − | You must supply 5 VDC power to the relay rack. This can be done in either of the following ways:
| + | |
| − | * Connect an external 5 VDC power source to the relay rack's +5V and GND terminals.
| + | |
| − | * Attach a wire on the bottom of the relay rack (via solder) from the +5V terminal to J1 pin 49.
| + | |
Latest revision as of 14:28, 19 February 2019
- REDIRECT 7501Tx relay racks