JM at 18:06, 6 December 2016

2016-12-06T18:06:42Z

← Older revision		Revision as of 13:06, 6 December 2016
Line 7:		Line 7:
	To Encode video a composite video source must be connected to video in and Ethernet must be connected.		To Encode video a composite video source must be connected to video in and Ethernet must be connected.

	Using a web browser connect to the 2453 ~~(default http://192.168.24.53) follow the link on the left side: Configure Stream A (http://192.168.24.53/setup_streama.htm) Here the various parameters of the encoder can be controlled.~~		Using a web browser connect to the 2453

	Once those setting are correct Follow the link Control Stream A ~~(http~~:~~//192.168.24.53/conrtol_streama~~.~~htm)~~ Here the address of the device receiving the digital stream and the port number open on that device must be entered.		[[File:2453index.jpg]]

			follow the link on the left side: Configure Stream A

			[[File:2453configA.jpg]]

			Here the various parameters of the encoder can be controlled.

			Once those setting are correct Follow the link Control Stream A

			[[File:2453controlA.jpg]]

			Here the address of the device receiving the digital stream and the port number open on that device must be entered.

	The receiving device should be ready to receive before the sending device starts sending.		The receiving device should be ready to receive before the sending device starts sending.
Line 17:		Line 29:
	To Decode video a composite video display must be connected to video out and Ethernet must be connected.		To Decode video a composite video display must be connected to video out and Ethernet must be connected.

	Using a web browser connect to the 2453 which will receive the digital stream ~~(default http~~:~~//192~~.~~168~~.24.~~53)~~		Using a web browser connect to the 2453 which will receive the digital stream

			note: each device on an Ethernet network must have a unique address, if two 2453's are being used the address of at least one must be changed through the Admin Network page

			[[File:2453AdminNet.jpg]]

			Follow the link on the left side: Configure output

			[[File:2453configOut.png]]

			Here the various parameters of the decoder can be controlled. The stream format setting must match the stream format setting of the encoder, ie if the encoder is configured to H264 VES the decoder must be set to H264 VES.

	~~note: each device on an Ethernet network must have a unique address, if two 2453's~~ are ~~being used~~ the ~~address of at least one must be changed through the Admin Network page (http://192.168.24.53/admin_network.htm)~~		Once those setting are correct Follow the link Control Output

	~~Follow the link on the left side~~: Configure output (http://192.168.24.53/setup_outputa.htm) Here the various parameters of the decoder can be controlled. The stream format setting must match the stream format setting of the encoder, ie if the encoder is configured to H264 VES the decoder must be set to H264 VES.		[[File:2453controlOut.png]]

	~~Once those setting are correct Follow the link Control Output (http://192.168.24.53/conrtol_output.htm)~~ Here the address of the device sending the digital stream and the port number to open to that device must be entered. The packet headers must be the same as on the sending device.		Here the address of the device sending the digital stream and the port number to open to that device must be entered. The packet headers must be the same as on the sending device.

	The receiving device should be ready to receive before the sending device starts sending. Click start on the receiving device before clicking start on the sending device.		The receiving device should be ready to receive before the sending device starts sending. Click start on the receiving device before clicking start on the sending device.

JM: Created page with "== Using a 2453 == A 2453 can take an NTSC or PAL composite video stream and convert it to a digital format or take one of those streams and output NTSC or PAL composite vide..."

2016-10-24T18:41:10Z

Created page with "== Using a 2453 == A 2453 can take an NTSC or PAL composite video stream and convert it to a digital format or take one of those streams and output NTSC or PAL composite vide..."

New page

== Using a 2453 ==

A 2453 can take an NTSC or PAL composite video stream and convert it to a digital format or take one of those streams and output NTSC or PAL composite video.

== Encoding video ==

To Encode video a composite video source must be connected to video in and Ethernet must be connected.

Using a web browser connect to the 2453 (default http://192.168.24.53) follow the link on the left side: Configure Stream A (http://192.168.24.53/setup_streama.htm) Here the various parameters of the encoder can be controlled.

Once those setting are correct Follow the link Control Stream A (http://192.168.24.53/conrtol_streama.htm) Here the address of the device receiving the digital stream and the port number open on that device must be entered.

The receiving device should be ready to receive before the sending device starts sending.

== Decoding video ==

To Decode video a composite video display must be connected to video out and Ethernet must be connected.

Using a web browser connect to the 2453 which will receive the digital stream (default http://192.168.24.53)

note: each device on an Ethernet network must have a unique address, if two 2453's are being used the address of at least one must be changed through the Admin Network page (http://192.168.24.53/admin_network.htm)

Follow the link on the left side: Configure output (http://192.168.24.53/setup_outputa.htm) Here the various parameters of the decoder can be controlled. The stream format setting must match the stream format setting of the encoder, ie if the encoder is configured to H264 VES the decoder must be set to H264 VES.

Once those setting are correct Follow the link Control Output (http://192.168.24.53/conrtol_output.htm) Here the address of the device sending the digital stream and the port number to open to that device must be entered. The packet headers must be the same as on the sending device.

The receiving device should be ready to receive before the sending device starts sending. Click start on the receiving device before clicking start on the sending device.

2453 Decoder - Revision history

JM at 18:06, 6 December 2016

JM: Created page with "== Using a 2453 == A 2453 can take an NTSC or PAL composite video stream and convert it to a digital format or take one of those streams and output NTSC or PAL composite vide..."