7501T8: Difference between revisions
Jump to navigation
Jump to search
+826 table |
|||
| Line 4: | Line 4: | ||
{| class="wikitable" | {| class="wikitable" | ||
! SSR | ! SSR | ||
! Header<br>Pin | ! Header<br>Pin | ||
! Terminal<br>Block Pins | ! Terminal<br>Block Pins | ||
| Line 57: | Line 57: | ||
|13-14 | |13-14 | ||
|6 | |6 | ||
| | |30 | ||
|13 | |13 | ||
|- | |- | ||
| Line 75: | Line 75: | ||
* Connect an external 5 VDC power source to the relay rack's +5V and GND terminals. | * Connect an external 5 VDC power source to the relay rack's +5V and GND terminals. | ||
* Attach a wire on the bottom of the relay rack (via solder) from the +5V terminal to J1 pin 49. | * Attach a wire on the bottom of the relay rack (via solder) from the +5V terminal to J1 pin 49. | ||
{| class="wikitable" | |||
! SSR | |||
! Model 826<br>J3 GPIO | |||
! Model 826<br>J4 GPIO | |||
|- | |||
|0 | |||
|0 | |||
|24 | |||
|- | |||
|1 | |||
|1 | |||
|25 | |||
|- | |||
|2 | |||
|2 | |||
|26 | |||
|- | |||
|3 | |||
|3 | |||
|27 | |||
|- | |||
|4 | |||
|4 | |||
|28 | |||
|- | |||
|5 | |||
|5 | |||
|29 | |||
|- | |||
|6 | |||
|6 | |||
|30 | |||
|- | |||
|7 | |||
|7 | |||
|31 | |||
|} | |||
Revision as of 15:24, 12 July 2018
Model 7501T8 is a solid-state relay (SSR) rack that accommodates up to eight G4 type SSR modules. It has a 50-pin header which is compatible with several Sensoray GPIO products, including models 826 and 2410.
Pinout
| SSR | Header Pin |
Terminal Block Pins |
Model 826 J3 GPIO |
Model 826 J4 GPIO |
Model 2410 GPIO |
|---|---|---|---|---|---|
| 0 | 47 | 1-2 | 0 | 24 | 17 |
| 1 | 45 | 3-4 | 1 | 25 | 19 |
| 2 | 43 | 5-6 | 2 | 26 | 21 |
| 3 | 41 | 7-8 | 3 | 27 | 23 |
| 4 | 39 | 9-10 | 4 | 28 | 9 |
| 5 | 37 | 11-12 | 5 | 29 | 11 |
| 6 | 35 | 13-14 | 6 | 30 | 13 |
| 7 | 33 | 15-16 | 7 | 31 | 15 |
Using with model 826
The relay rack can be connected to header J3 or J2 on the 826 board.
You must supply 5 VDC power to the relay rack. This can be done in either of the following ways:
- Connect an external 5 VDC power source to the relay rack's +5V and GND terminals.
- Attach a wire on the bottom of the relay rack (via solder) from the +5V terminal to J1 pin 49.
| SSR | Model 826 J3 GPIO |
Model 826 J4 GPIO |
|---|---|---|
| 0 | 0 | 24 |
| 1 | 1 | 25 |
| 2 | 2 | 26 |
| 3 | 3 | 27 |
| 4 | 4 | 28 |
| 5 | 5 | 29 |
| 6 | 6 | 30 |
| 7 | 7 | 31 |