File list

Jump to navigation Jump to search

This special page shows all uploaded files.

File list
First pagePrevious pageNext pageLast page
Date Name Thumbnail Size User Description Versions
16:47, 29 March 2017 518 photo.jpg (file) 246 KB JL (talk | contribs) Reverted to version as of 17:48, 11 March 2016 3
08:31, 1 March 2017 826 3Phase pwm.png (file) 32 KB JL (talk | contribs) fixed dio/counter routability 3
17:42, 28 February 2017 826 quadrature gen.gif (file) 16 KB JL (talk | contribs) corrected dio/counter matching 2
10:49, 22 February 2017 826 estop.gif (file) 7 KB JL (talk | contribs) A robust way to connect a 24VDC emergency-stop contact to model 826. 1
13:06, 6 December 2016 2453controlOut.png (file) 113 KB JM (talk | contribs) 2453 output control page taken using fw 1270 1
13:05, 6 December 2016 2453configOut.png (file) 146 KB JM (talk | contribs) 2453 output config page created using fw 1270 1
12:29, 6 December 2016 2453AdminNet.jpg (file) 175 KB JM (talk | contribs) 2453 network admin page from the manual 1
12:29, 6 December 2016 2453controlA.jpg (file) 101 KB JM (talk | contribs) 2453 control stream A from the manual 1
12:28, 6 December 2016 2453configA.jpg (file) 155 KB JM (talk | contribs) 2453 configure stream A from the manual 1
12:27, 6 December 2016 2453index.jpg (file) 67 KB JM (talk | contribs) 2453 index.htm from the manual 1
11:31, 6 December 2016 Index.jpg (file) 67 KB JM (talk | contribs) jpeg picture of 2453 index.htm page out of the manual 1
09:18, 9 November 2016 826 ttl encoder.gif (file) 27 KB JL (talk | contribs) Wiring diagram showing how to connect two TTL/CMOS-compatible single-ended incremental encoders to the 826 board using counter channels 0 and 1. 1
13:15, 4 November 2016 826 encoder FLT.png (file) 13 KB JL (talk | contribs) Using an 826 counter channel to monitor an incremental encoder's active-low FAULT output. The differential pair is swapped between line driver and receiver so that a disconnected or unpowered encoder will be recognized as a fault. 1
13:02, 1 September 2016 SmartAD pinout.gif (file) 39 KB JL (talk | contribs) Connector pinout used by Sensoray Smart A/D boards (e.g., model 418, 419, 518, 618, 619). For each sensor channel x (in range 0:7), PHx/PLx supply excitation to a passive sensor (if needed) and SHx/SLx are the differential analog inputs. TREF and +12V ... 1
11:54, 4 August 2016 Clock filter minimum.png (file) 13 KB JL (talk | contribs) 826 counter timing diagram showing external clock filtering with zero filter delay (filter is disabled). 1
11:53, 4 August 2016 Clock filter general.png (file) 19 KB JL (talk | contribs) 826 counter timing diagram showing general case for external clock filtering. 1
11:51, 4 August 2016 826 counter timing.png (file) 21 KB JL (talk | contribs)   2
07:33, 9 June 2016 826 serial data capture.png (file) 7 KB JL (talk | contribs) Using an 826 counter channel to capture data from a serial data source. Each data edge causes a counter snapshot that contains a reason code and timestamp. 1
10:32, 26 May 2016 2410.jpg (file) 81 KB JL (talk | contribs) Model 2410 is a compact open-frame module that interfaces 48 general-purpose TTL/CMOS compatible digital input/output (DIO) signals to Ethernet. 1
10:51, 11 May 2016 826PwmWatchdog.gif (file) 27 KB JL (talk | contribs) show inverted DIO output; label DIO_out router 2
12:39, 21 March 2016 518 power.jpg (file) 171 KB JL (talk | contribs) Power supply test points on model 518. 1
16:56, 4 April 2014 2255 photo.jpg (file) 68 KB JL (talk | contribs) Model 2255 1
16:41, 4 April 2014 826 photo.jpg (file) 1.81 MB JL (talk | contribs) Sensoray model 826 board 1
16:31, 4 April 2014 2226 photo.jpg (file) 190 KB JL (talk | contribs) Sensoray Model 2226 1
16:09, 25 April 2013 AdgGroundReference.gif (file) 8 KB JL (talk | contribs) cropped 2
First pagePrevious pageNext pageLast page